Why use litz wires?

Litz wires consist of multiple rope-like bunched single insulated wires and are used in a wide range of applications requiring good flexibility and high frequency performance.

HF-litz wires are produced using multiple single wires electrically isolated from each other and are typically used in applications operating within a frequency range of 10 kHz to 5 MHz. Increasing frequencies cause the current to flow in the perimeter area or even along the surface of each conductor - this is known as the "skin effect". Similar By this the cross section carrying the current is reduced causing losses at this high frequency. In addition, losses at higher frequencies are caused by the "proximity effect", where the neighboring electrical field negatively affects the electromagnetic distribution against each other. Litz wires engineered twisted construction using multiple insulated wires can effectively minimize these high frequency losses.

Subsequent sections give an overview of basic terms and variants of litz wire.

 

 

Single Wire

The basic component of a litz wire is the insulated single wire. Conductor material and enamel insulation can be combined optimally to meet the demands of specific applications.

back

 

Length of Lay

The length of lay describes the distance which a single wire needs for one complete rotation around the litz wire circumference (360 degrees).

back

 

Pitch Direction

S-lay
Z-lay

The pitch direction indicates the twist or bunching direction of the bundled wire construction. Z-lay is bunched in a clockwise direction while S-lay is the opposite, or counter-clockwise twist direction.

back

 

Directly Bunched Litz Wires

Directly bunched Construction

Any number of single wires are directly bunched so each individual wire is freely located. The single wires can take any position within the litz wire cross section.

back

 

Concentrically Bunched Litz Wires

Concentric Design

The individual wires are positioned in one or more layers concentrically around the litz wire center conductor. In this design configuration each single wire naturally moves into its predefined position during the twisting operation resulting in consistent dimensions and working properties.

Multi-step Litz Wires

Multi-step Design

Depending on the specified profile, litz wires can be twisted in several steps. Any number of pre-twisted bundles are stranded with each other in several twisting steps. The electrical and mechanical properties of the final product depend upon the designed litz wire construction.

                  

 

back

 

Basic Litz Wires

Litz wires twisted in one or several steps without any additional coating such as serving, extruding or other functional coating.

back

 

Served Litz Wire

Litz wires can be spirally served with different materials such as nylon or natural silk. During the serving process the litz wire is covered by a textured yarn in one or more layers. Litz wire dimensional stability, flexibility and impregnation performance are improved with he addition of served materials.

back

 

Taped Litz Wires

An additional insulating coating of the litz wire can be added by taping the outer litz surface with one or more tapes. Increased dielectric breakdown voltage, thermal endurance as well as flexibility can be achieved by a suitable combination of taping material, number of tapes and the degree of overlapping of the tapes.

back

 

Degree of Overlapping

The degree of overlapping of two adjacent tape windings is defined by the gradient angle between tape and litz wire during the taping process. The overlapping determines the number of tape layers located on top of each other and thus the insulation thickness of the litz wire. 

 

 

 

back

 

Extruded Litz Wires

Coating litz wires with extruded thermoplastic materials offers additional possibilities to insulate litz wire conductors. Extruded coatings are highly flexible and can provide additional protection against moisture and chemical attack.

back

 

Profiled Litz Wires

Basic litz wires and some types of served or taped litz wires can be given a square or rectangular cross section by a profiling process. The compacted profile provides an optimized copper filling factor for more efficient electrical properties in applications of the wound coil.

back

 

Litz Wires with Strain Relief

Ultra-fine litz wires or litz wires requiring increased tensile strength or flex life performance can be improved with the addition of strain relief from high-strength mono- or multifilament materials. To achieve an optimal force absorption, the strain relief materials are arranged in the center of concentric litz wire constructions. For bunched litz wires, a non concentric arrangement using a bare conductor wire as the strain relief member is also possible.

 

back

 

Smartbond Litz Wires

Self supporting coils can be produced using litz wires provided with a 'Smartbond' adhesive in automated winding processes. Very thin coils can be produced with Smartbond's unique construction providing additional space for designers or to help achieve miniaturization goals.